● Measuring input type : DC current / DC voltaget / Potentiometer / Linear Resistance / RTD / TC
● More output type ─ analogue output / relay / RS-485
● Extraction of square root ─ input : voltage, current
● Option RS-485 communication function can do 10-point linear calibration function
● Signal isolation, preventing noise, filtering function : provide safe and stable measuring
● Power supply : 85~253 VAC, 50~60Hz;auxiliary supply output ( 18~26VDC / 50 mA ) : use for 2-wire & 3-wire transmitter
● User-friendly, interactive operation interface. 
● Panel installation, High light red LED display panel,  14.1mm height of character, 5 digits, -9.9.9.9~+9.9.9.9.9,  7-segment display
● Programmable, high safety & stability, fire-proof case, moisture-proof cover

display 
display readout : 5 digits ( -9.9.9.9 ... +9.9.9.9.9 )
decimal point : 0 ... 4 place, button
display : highlight red LED ( brightness can be adjusted ) 
digit height :  14.1 mm
accuracy : 0.1 % F.S. ± 1 digital
sampling time : 4 cycle / sec
response time adjustment range : 0.5 ... 60 sec
parameter setting mode : button
input
voltage : 0 ... 10V, 2 ... 10V, 0 ... 1V, 0.2 ... 1V, 1 ... 5V
current : 0 ... 20mA, 4 ... 20mA
RTD : Pt10, Pt20, Pt50, Pt100, Pt200, Pt250, Pt300,
Pt400, Pt500, Pt1000 2/3/4w
TC : B, E, J, K, N, R, S, T, U ( internal CJC function )
Linear Resistance 0 ... 10K Ohms
Potentiometer 10 ... 100K Ohms
analogue
output
current : 0-20mA, 4-20mA,20-0mA 20-4mA
voltage : 0-1V, 0.2-1V,0-5V,1-5V, 0-10V, 2-10V,1-0V,1-0.2V,5-0V,5-1V,10-0V,10-2V
load resistance : current:RL< 500 Ohm.;voltage≧10KΩ
analogue output resolution : 16 bit
signal error detection : yes
relays
alarm hysteresis : display value or 0~100%
ON and OFF delay : 0~3600s
output signal error detection : yes     
relay actuation direction : upper limit : HI, AL ; lower limit : LO, AL
relay capacity : Max current : 6A
                          Max voltage : 277VAC / 30VDC            
                          Max power : 1500VA / 180W
communication
communication methods & protocol : RS-485 Modbus RTU,master or slave
RS-485 baud rate : 9600, 19200, 38400, 57600, 115200 bps
environment
operating environment : -10 to +60°C ; 0~95% ( non-cond. )
storage environment : -25 to +60°C
electrical
power supply / voltage : 85~253VAC, 50~60Hz
auxiliary power : 18-26VDC/50mA
insulation voltage endurance : 2KVac/1min 
parameter memory type : FLASH
dissipated power : 5W
isolation
power supply / analogue input / analogue output / RS-485
protect
protect rating : IP65 ( front panel )
electric protection : polarity protection & over-voltage
certification
CE
material
case : ABS fire-proof class ( UL94V-0 )
dimensions ( HxWxD ) : 48 x 96 x 94.45 mm
cut out dimensions : 42.5 x 90.5 mm ( + 1 mm )
weight : about 230 g

The specifications contained herein are subject to change without notice and any user of said specifications should verify from the manufacturer that the specifications are currently in effect. Otherwise, the manufacturer assumes no responsibility for the use of specifications which may have been changed and are no longer in effect.

*Please make sure the product and the device which connect with RS485 are on common ground, avoid damaged product. 


Option list
8205001010
Cold junction compensation resistor
Industry / Agriculture / Pottery & Glass / Chemical Industry / Transportation 
Technology / Energy / Eco-friendly /  Oil & Gas / Water Circulation System / Marine 
Factory Automation / Metal & Steel / Cement / Pulp & Paper / Pharmaceuticals / Food & Beverage