• GS07 CO2 Transmitter

GS07 CO2 Transmitter

Model : GS07
Features : Suitable for light industry. Compact size. Easy to install.
Sensor type : Non-dispersive infrared(NDIR)waveguide technology
Measuring range : 0 ... 20,000 (PPM)
Output : RS-485 / 0 ... 10 V / 4 ... 20 mA
Accuracy : ±40 PPM±3% of reading (2000/5000 PPM)
±200 PPM±3% of reading (10000/20000 PPM)
IP rating : IP54(Clamp) / IP65(Flange)
  • Features
    ● Using patented state-of-the-art non-dispersive infrared(NDIR)wave-guide technology and offers reliable measurements
    ● Comply to EMC directive 2014 / 30 / EU
    ● CO2 Measuring range:0 … 2,000 / 0 … 5,000 / 0 … 10,000 / 0 … 20,000(PPM) (Max.:50,000 PPM);IP65 / IP54
    ● Digital output(RS-485 Modbus RTU protocol, 0 ... 6000 PPM), analog output(0 … 10 V, 4 … 20 mA)
    ● Maintenance-free in most HVAC ventilation applications
    ● High tolerance to extreme humidity environment conditions
    ● Non-frill design, direct DDC connection


    eyc-tech GS07 is a state-of-the-art non-dispersive infrared(NDIR)carbon dioxide(CO2 )transmitter. The direct insertion design and miniature size make it easy to install in the ventilation duct. eyc-tech GS07 provides measurement in analog outputs(0 … 10 V, 4 … 20 mA)and digital output(RS-485 Modbus RTU protocol). With CO2 demand controlled ventilations, eyc-tech GS07 helps to save money by decreasing the energy consumption while maintaining a healthier indoor climate
  • Applications
    Greenhouses / Mushroom farming / Industrial safety / AHUs in high RH regions
  • Download
  • Specification
    CO2 Measuring range
    0 … 2,000 / 0 … 5,000 / 0 … 10,000 / 0 … 20,000 (PPM) (Max. : 50,000 PPM)
    Output
    RS-485
    Digital output with Modbus RTU protocol
    Voltage signal terminal CO2 Note 3
    Voltage or current output : Jumper selection(Default 0 … 10 V)
    D/A resolution : 10 bits(10 mV / 0.016 mA)
    D/A conversion accuracy : ±2% of reading±50 mV
    Electrical characteristics : Voltage output-ROUT<100 Ω, RLOAD>5 kΩ
    Current output-RLOAD<500 Ω
    Operating temperature range
    0 … 50°C
    Storage temperature range
    -40 … +70°C
    Operating humidity range
    0 … 100% RH(Sensor in powered-up condition)
    Operating environment
    Residential, commercial and industrial spacesNote 1
    Warm-up time
    ≦1 min(at full specs≦15 min)
    Sensor life expectancy
    >15 years
    Duct air velocity
    Direct insertion sensor, no minimum airs peed requirement
    Maintenance interval
    No maintenance Note 2(with ABC algorithm)
    Power input
    AC / DC 24 V±20%, 50 Hz or 60Hz(Half-wave rectifier input)
    Power consumption
    <1 W average
    Connection wires
    M12 male connector for power input (G+, G0) & voltage/current output (Out)
    with M12 female quick connection cable (AWG24 wires)
    Sensing method
    Non-dispersive infrared(NDIR)wave-guide technology with
    Automatic Background Calibration(ABC)and passive gas diffusion(No moving parts)
    Response time(T1/e)
    <10 sec(at 30 cc/min flow rate)/ <3 min diffusion time
    Repeatability
    ±30 PPM±1% of reading
    Accuracy at 25°C Note 1,2
    ±40 PPM±3% of reading (2000/5000 PPM), ±200 PPM±3% of reading (10000/20000 PPM)
    Annual zero drift Note 1,2
    <±10 PPM(with ABC function)
    Pressure dependence
    +1.6% reading per hPa
    Installation support
    Background level calibration adjustment jumper trigger(bCAL)
    Dimension
    94x30 mm diameter
    Duct probe length
    51 mm
    IP rating
    IP65
    Compliance with EMC directive
    2014 / 30 / EU
    Note 1: The SO2 enriched environments are excluded.
    Note 2: In normal IAQ applications(at NTP). Accuracy is defined after minimum 3 weeks of continuous operation. The tolerance of the span calibration gas (2% unless otherwise requested)and test gas adds to the total uncertainty.
    Note 3: The specifications are valid for the output load connected to ground G0. Other outputs and measurement ranges are available per request.

Note : Design and specifications are subject to change without notice.
Note : If the product has RS-485 function, to avoid damaging product, please make sure the product and the device which connect with RS-485 are on common ground.